Custom dust collection, blow pipe, plenums, and welded duct built to your spec and installed in your plant. Carbon steel, stainless, aluminum, and specialty alloys. One stop shop from design to field installation.
A.M. Metal designs, fabricates, and installs commercial and industrial ductwork for manufacturing plants, processing facilities, and the contractors who serve them. We are a single source for the whole job: we engineer the system, build it in our South Williamsport shop, and send our own crews to install it in the field.
Most of our ductwork work falls into four categories:
Custom piping, chutes, and blow pipe systems that pull dust, shavings, trim, and particulate off your equipment and out of your air. This is a large part of what we do, from a single run to a full plant system.
Welded duct for food-grade, sanitary, and specialty environments, including stainless and aluminum work where a clean, sealed system is the requirement, not an upgrade.
Supply and return duct, plenums, custom transitions, and offsets that tie new equipment into existing systems. We build outlet plenums for furnaces, transitions off bottom-discharge and rooftop units, and the custom connections that never come standard.
Boiler exhaust systems and automatic damper work, including the automatic closing dampers that tie into your equipment and keep the system running safely.
We work in food and beverage plants and processors, Pharmaceutical and clean-process facilities, Manufacturing and industrial operations. We’re also set up for Public and institutional projects (rate work) – the prevailing-wage and union jobs that come with public projects. State jobs, schools, colleges and universities, government buildings: we meet the labor and documentation requirements those jobs carry, and we hold them to the same standard as everything else we build.
The right ductwork starts with the right material, and the right gauge. A system built too light fails — we have been called in to replace duct that was specified in too thin a gauge and collapsed under its own suction. We help you match the material and thickness to the job so the system lasts.
We fabricate in:
the workhorse for most industrial duct and structural runs.
in multiple grades suited to food, pharmaceutical, sanitary, and corrosive applications.
for lighter-weight and specialty applications.
Specialty alloys and sourced materials. If a job calls for something out of the ordinary - titanium, for example. we can price it and source it.
We are a US Duct dealer, supplying and fabricating the clamp-together spiral dust collection ducting system, which is built to SMACNA standard. On most of our own fabrication, we go above and beyond SMACNA standards.
If you already know what you need, we speak your language: plenums and outlet plenums, custom transitions and offsets, blow pipe, custom chutes, Ductmate frame connections, Vanstone ring connections, and welded duct for sanitary work.
A lot of ductwork problems come from a handoff: one company designs it, another builds it, a third installs it, and when something does not fit, everyone points at someone else.
A.M. Metal keeps the whole job under one roof. We design the system, fabricate it in our shop, and send our own experienced crews to install it in your facility. That means:
Honest answers. If you bought a used dust collector that we cannot stand behind, we will tell you before it goes in, not after.
Over 40 years of hands-on ductwork experience from Dave Danniker, plus more than 20 years of ductwork and metalwork experience from Jeremy.
Certified welders, tested for specific weld types on request when a job requires it.
Built to OSHA, NFPA, and SMACNA standards — and on our own fabrication, routinely above and beyond SMACNA.
We do not chase the lowest-price, one-and-done jobs. We build relationships, and our customers come back.
Here is some of what they say:
A.M. Metal is based in South Williamsport, Pennsylvania, and serves our home counties of Lycoming, Tioga, Columbia, Bradford, Sullivan, Clinton, Montour, Union, and Northumberland, along with the surrounding states of New York, New Jersey, Ohio, Maryland, West Virginia, and Delaware. Beyond our home region, we serve customers across the USA and beyond.
For the right project, we travel. We have built and installed ductwork as far as Connecticut, South Carolina, and Florida, and our team has taken jobs across the country and overseas. If your facility is outside our home region, ask — distance is rarely the deciding factor when the work is specialized.
We provide fabrication services across a wide range of industries, including:
Send us your drawings or a list, tell us about your dust collection project, or have us come out and field measure. One shop, from design to installation.
